Get all the Information About Network Appliance NS0-593 Exam 2026 Practice Test Questions
Check Real Network Appliance NS0-593 Exam Question for Free (2026)
NEW QUESTION # 13
A customer calls you to troubleshoot a network issue. The customer wants to create a packet trace for allclients
on the 192.168.9.0/24 subnet.
Referring to the exhibit, on which interface do you have to run the packet trace?
- A. a0a-322
- B. e2a-100
- C. a0a-456
- D. e2a-1092
Answer: D
NEW QUESTION # 14
When an administrator tries to create a share for an existing volume named voll, the process fails with an error.
Referring to the exhibit, what Is the reason for the error?
- A. The CIFS service is not authenticating properly with the domain controller.
- B. The volume has not beenmounted.
- C. The CIFS service is not in workgroup mode.
- D. The volume must have a type of DP.
Answer: B
NEW QUESTION # 15
You Just used the CLI to create a NetApp ONTAP FlexGroup Volume on a NetApp Cloud Volumes ONTAP instance. After creation, you notice odd behavior in NetApp Cloud Manager.
In this scenario, what Is the reason for this behavior?
- A. The Capacity Management Mode within Cloud Manager should be set to Automatic.
- B. Cloud Manager must be used to provision the FlexGroup volume.
- C. Cloud Volumes ONTAP does not support FlexGroup volumes.
- D. The Capacity Management Mode within Cloud Manager should be set to Manual.
Answer: D
Explanation:
= According to the NetApp Knowledge Base1, while Cloud Volumes ONTAP supports FlexGroup volumes, Cloud Manager does not. If you create a FlexGroup volume from System Manager or from the CLI, then you should set Cloud Manager's Capacity Management mode to Manual. Automatic mode might not work properly with FlexGroup volumes. The other options are incorrect because Cloud Volumes ONTAP does support FlexGroup volumes2, the Capacity Management Mode should not be set to Automatic, and Cloud Manager is not required to provision the FlexGroup volume3. Reference = 1, 2, 3
NEW QUESTION # 16
You notice poor performance on your FlexGroup and execute the system node run -node * flexgroup show command for more Information. You notice the "Urge" column has non-zero values.
In this scenario, which statement is true?
- A. The constituent volumes are out of Inodes.
- B. The constituent volumes are completely full.
- C. The aggregate is completely full.
- D. The data placement is uneven.
Answer: D
Explanation:
= The "Urge" column in the flexgroup show command indicates the urgency of data rebalancing for each constituent volume. A non-zero value means that the data placement is uneven across the volumes, which can affect the performance of the FlexGroup. The target value is the desired percentage of data for each volume, and the difference value is the deviation from the target. The FlexGroup tries to balance the data placement by moving data between the volumes, but this process can be slow or interrupted by other factors. Therefore, it is recommended to monitor the "Urge" column and take corrective actions if the values are high or persistent. Reference = What do "flexgroup show" target and urgency and other columns mean?, NetApp ONTAP FlexGroup volumes - Best practices and implementation guide
NEW QUESTION # 17
Your customer complains that u host will constantly report losing a connection to the iSCSl target and then report that the session was reestablished.
As shown in the exhibit, what is a cause of this flapping?
- A. A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 have the same IQN.
- B. A host with an IP address of 172.20.10.80 and a second IP address of 10.10.20.60 is accessing different LUNs.
- C. A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 are in different initiator groups.
- D. A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 are accessing the same LUN.
Answer: A
Explanation:
IQN stands for iSCSI Qualified Name, which is a unique identifier for an iSCSI initiator or target1.
ONTAP uses IQN to authenticate and authorize iSCSI sessions2.
If two hosts have the same IQN, they will cause a conflict and ONTAP will reject the new session request from the second host3.
This will result in the host losing the connection to the iSCSI target and then reporting that the session was reestablished, as shown in the exhibit.
To avoid this problem, each host should have a unique IQN. Reference:
iSCSI Qualified Name (IQN) - NetApp
iSCSI authentication and authorization - NetApp
Troubleshooting iSCSI issues - NetApp
[Configuring iSCSI initiators - NetApp]
NEW QUESTION # 18
You receive the "Unable to connect to the management gateway server"error when trying to connect to a node
management IP.
In this situation, how do you determine whether core dumps are generated for the mgwd user space process?
- A. Log in to the nodeshell using the node console and collect the core dumps from the nodeshell.
- B. Log in to the clustershell using the node console and collect the core dumps from the clustershell.
- C. Log in to the systemshell and collect core dumps from thesystemshell.
- D. Log in to the service processor and collect the core dumps from the service processor.
Answer: D
NEW QUESTION # 19
You have connection Issues from a Linux host to an AFF A400 FC LUN. You are asked by support to run the NetApp sanlun command to provide troubleshooting information.
Which NetApp software package must be installed on the host?
- A. Host Utilities package
- B. SnapDrive for UNIX
- C. Inventory Collect Tool
- D. Virtual Storage Console
Answer: A
Explanation:
= The NetApp sanlun command is a tool that returns information about the LUNs mapped to your host, multipathing, and information necessary to create initiator groups. It is part of the Linux Unified Host Utilities package, which also includes other tools to manage NetApp storage, such as failover policies and physical paths. To run the sanlun command, you must install the Host Utilities package on your Linux host. The other options are not relevant for this scenario, as they are either not required or not compatible with the Linux host. Reference = Install Linux Unified Host Utilities 7.1, SAN Toolkit
NEW QUESTION # 20
Which two statements about NetApp Cloud Volumes ONTAP licenses ate true? (Choose two.)
- A. Having an Essentials package enables you to convert to another licensing option.
- B. Capacity-based license packages support only single-node configurations.
- C. BYOL licenses are purchased directly from NetApp.
- D. AWS Marketplace contracts cannot be mixed with BYOL.
Answer: A,C
Explanation:
Having an Essentials package enables you to convert to another licensing option. This is true because the Essentials package is a capacity-based licensing option that allows you to pay for Cloud Volumes ONTAP per TiB of capacity. You can switch to another capacity-based package or to a Keystone Flex Subscription at any time1.
BYOL licenses are purchased directly from NetApp. This is true because BYOL stands for Bring Your Own License, which means you need to obtain a license from NetApp before deploying Cloud Volumes ONTAP systems in any cloud provider2.
Capacity-based license packages support only single-node configurations. This is false because capacity-based license packages support both single-node and HA configurations1.
AWS Marketplace contracts cannot be mixed with BYOL. This is false because you can mix AWS Marketplace contracts with BYOL as long as the license type matches the instance type3. Reference: 1: Cloud Volumes ONTAP licensing | NetApp Documentation 2: Set up licensing for Cloud Volumes ONTAP in Google Cloud - NetApp 3: Set up licensing for Cloud Volumes ONTAP in AWS - NetApp
NEW QUESTION # 21
You are deploying NetApp ONTAP Select. When trying to add VMware vCenter to the inventory, you receive
the message shown below.
Credential authentication failed for x.x.x.x with: HostConnectionFailed
In this scenario, how would you correct this problem?
- A. Change the vCenter password.
- B. Change the IP address of the vCenter server.
- C. Change the IP address of the ONTAP Select Deploy VM.
- D. Change the gateway address of the ONTAP Select Deploy VM.
Answer: A
NEW QUESTION # 22
You are optimizing your Cloud Volumes ONTAP. For interoperability and consolidation purposes, you need
to know the storagelimits.
In this scenario, which source should be reviewed?
- A. Cloud Central
- B. Hardware Universe
- C. Interoperability Matrix Tool (IMT)
- D. NetApp Cloud Volumes ONTAP Release Notes
Answer: D
NEW QUESTION # 23
After users start reporting the Inability to create new flies in a CIFS share, you find EMS events for
wafl.dir.size.max logged for the volume of the SVM to which the share points.
In this scenario, which action should you take to solve this issue?
- A. Increase the maximum directory size for the volume.
- B. Increase the maximum numberof files for the volume.
- C. Move the volume to a different aggregate.
- D. Delete unneeded files from the directory.
Answer: B
NEW QUESTION # 24
You have connection Issues from a Linux host to an AFF A400 FC LUN. You are asked by support to run the
NetApp sanlun command to provide troubleshooting information.
Which NetApp software package must be installed on the host?
- A. Host Utilities package
- B. SnapDrive for UNIX
- C. Inventory Collect Tool
- D. Virtual Storage Console
Answer: A
NEW QUESTION # 25
You have a 4-node NetApp ONTAP 9.8 cluster with an AFF A400 HA pair and a FAS8300 HA pair with 16 TB NL-SAS drives. You are asked to automatically tier 150 TB of Snapshot copy data from the AFF A400 aggregates to the FAS8300.
In this scenario, which ONTAP license must be added to the cluster to accomplish this task?
- A. TPM license
- B. VE license
- C. FabricPool license
- D. S3 license
Answer: C
NEW QUESTION # 26
After users start reporting the Inability to create new flies in a CIFS share, you find EMS events for wafl.dir.size.max logged for the volume of the SVM to which the share points.
In this scenario, which action should you take to solve this issue?
- A. Increase the maximum number of files for the volume.
- B. Increase the maximum directory size for the volume.
- C. Move the volume to a different aggregate.
- D. Delete unneeded files from the directory.
Answer: B
Explanation:
The wafl.dir.size.max event occurs when a directory has reached its maximum directory size (maxdirsize) limit, which prevents new file creation in that directory. The maxdirsize is a volume-level option that can be modified using the volume modify command. To solve this issue, you should increase the maximum directory size for the volume that contains the CIFS share, as long as it does not exceed 3% of the physical memory. Alternatively, you can reorganize the directory structure to avoid having too many files in one directory. Reference = Max Directory size error - NetApp Knowledge Base How to identify the target directory of wafl.dir.size.warning - NetApp Knowledge Base Post about wafl.dir.size.max | Source.kohlerville.com WAFL Max dirsize | uadmin
NEW QUESTION # 27
Your customer wants to access a LUN on a FAS 8300 system from a VMware ESXi server through the FC protocol. They already created a new SVM, volume. LUN, and igroup for this purpose. The customer reports that the server's FC HBA port Is online, but the LUN does not show up.
Referring to the exhibit, what is the reason for this problem?
- A. The zoning on the FC switches Is Incorrect.
- B. The FC service has not been configured on the SVM.
- C. The esxserver igroup contains incorrect IQNs.
- D. The LUN Is not mapped to the correct SCSI ID.
Answer: B
Explanation:
To access a LUN on a FAS 8300 system from a VMware ESXi server through the FC protocol, the customer must configure the FC service on the SVM that owns the LUN. The FC service enables the SVM to act as an FC target and communicate with the FC initiators on the host. Without the FC service, the LUN will not be visible to the host, even if the LUN is mapped to an igroup and the FC LIFs are up. The exhibit shows that the FC service is not configured on the SVM, as the output of the command vserver fcp initiator show -vserver SVM1 is empty. Therefore, the reason for the problem is that the FC service has not been configured on the SVM. Reference = Configure an SVM for FC, Create an FC protocol service, Single IQN iSCSI session with ESXi on ONTAP when igroup has two IQNs
NEW QUESTION # 28
You have a 4-node NetApp ONTAP 9.8 cluster with an AFF A400 HA pair and a FAS8300 HA pair with 16 TB NL-SAS drives. You are asked to automatically tier 150 TB of Snapshot copy data from the AFF A400 aggregates to the FAS8300.
In this scenario, which ONTAP license must be added to the cluster to accomplish this task?
- A. TPM license
- B. VE license
- C. FabricPool license
- D. S3 license
Answer: C
Explanation:
FabricPool is an ONTAP feature that enables tiering of cold data from SSD aggregates to low-cost object storage, either on-premises or in the cloud1. FabricPool requires a license to be installed on the cluster, and the license type depends on the cloud tier being used2. In this scenario, the cloud tier is another ONTAP cluster (FAS8300), which is not supported by the new Cloud Tiering license that is used for most FabricPool configurations3. Therefore, the old FabricPool license that is retained for dark sites or MetroCluster systems using FabricPool Mirror must be used3. The FabricPool license defines the amount of capacity that can be tiered to the cloud tier, and it can be increased by add-on orders4. Reference:
1: FabricPool overview5
2: FabricPool requirements6
3: Install a FabricPool license2
4: ONTAP FabricPool (FP) Licensing Overview1
NEW QUESTION # 29
......
Use Free NS0-593 Exam Questions that Stimulates Actual EXAM : https://www.practicedump.com/NS0-593_actualtests.html
Get Ready to Boost your Prepare for your NS0-593 Exam with 62 Questions: https://drive.google.com/open?id=1D10g0cpGDf4PomoKOq6U7PEcrOtTPptU