NACE-CIP1-001 Dumps for Pass Guaranteed - Pass NACE-CIP1-001 Exam 2024
NACE-CIP1-001 Exam Dumps - Try Best NACE-CIP1-001 Exam Questions from Training Expert PracticeDump
NACE-CIP1-001 Coating Inspector Level 1 exam is recognized globally and is highly respected in the coating inspection industry. Coating Inspector Level 1 certification program is designed to provide individuals with the necessary skills and knowledge to perform basic coating inspections. The program is ideal for individuals who are looking to improve their skills and knowledge in the coating inspection industry and to become certified coating inspectors.
NACE-CIP1-001 (Coating Inspector Level 1) Certification Exam is a globally recognized certification that validates the skills and knowledge of individuals working in the field of coating inspection. Coating Inspector Level 1 certification exam is designed to assess the competence of coating inspectors in the application and inspection of protective coatings on steel and other substrates. It is an important credential for professionals who wish to advance their careers in the coatings industry.
NEW QUESTION # 16
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
Answer: B
NEW QUESTION # 17
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the less aggressive profile
- B. Record your result by identifying two segments
- C. Record the segment with the more aggressive profile
- D. Use another method as the comparator method is too subjective
Answer: A
NEW QUESTION # 18
Prior to using Inspection Tools the inspector must:
- A. Be trained on how to use the instrument
- B. Read the manufactures' instructions
- C. Ensure the instrument is within calibration parameters
- D. a), b) & c)
Answer: D
NEW QUESTION # 19
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. grease and oil
- B. inhibitor residues
- C. soluble chemical salts
- D. sulfates
Answer: A
NEW QUESTION # 20
NACE Level 1 Inspectors have been trained to perform:
- A. All types of inspection
- B. Visual inspection and Non-destructive testing
- C. Visual inspection only
- D. Visual inspection, Non-Destructive and Destructive testing
Answer: B
NEW QUESTION # 21
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Surface Temperature
- B. High Relative Humidity
- C. Low Surface Temperature
- D. Low Relative Humidity
Answer: D
NEW QUESTION # 22
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A general guide
- B. Pass/fail criteria
- C. A method to grade surface profile
- D. A final conflict resolution method
Answer: A
NEW QUESTION # 23
Passivation can best be described as:
- A. Complete elimination pf the corrosion process
- B. Treating metal with a liquid inhibiter
- C. A protective metallic oxide surface layer that slows corrosion
- D. A coating layer applied to the surface to inhibit corrosion
Answer: C
NEW QUESTION # 24
SSPC SP 1 identifies the use of:
- A. Biodegradable detergents
- B. Organic solvents
- C. Inorganic solvents
- D. A wide variety of materials
Answer: D
NEW QUESTION # 25
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. direct and perform the work stated in the specification.
- C. observe and report the quality of the work performed.
- D. observe and direct the work of the contractors.
Answer: C
NEW QUESTION # 26
What is used to determine compressed air cleanliness?
- A. Psychrometer
- B. Needle pressure gauge
- C. Blotter test
- D. Profilometer
Answer: D
NEW QUESTION # 27
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To dissolve the resin
- C. To control the evaporation rate
- D. To promote faster cure
Answer: C
NEW QUESTION # 28
Non Conformance Reports are completed by the Inspector:
- A. When the Inspector deems it to be a significant non-conforming item
- B. When the Inspector and Contractor deem it to be a significant non-conforming item
- C. In accordance with the specification's definition of a non-conformance
- D. In every instance that an item does not meet the specification requirements
Answer: B
NEW QUESTION # 29
If inspectors identify issues of non-conformance during an inspection, they should
- A. perform additional tests secretly to ensure there are no other potential issues at the site
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
Answer: D
NEW QUESTION # 30
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. when the coating will be reapplied.
- B. what materials were used.
- C. what items were coated.
- D. how the item was coated.
Answer: D
NEW QUESTION # 31
ISO SA 2 is defined as:
- A. Light Blast Cleaning
- B. Thorough Blast Cleaning
- C. Near White Metal Blasting
- D. Very Thorough Blast Cleaning
Answer: B
NEW QUESTION # 32
Removal of surface contaminants is done by:
- A. A combination of methods
- B. Abrasive blasting
- C. Scarifying
- D. Waterjetting
Answer: A
NEW QUESTION # 33
The Inspector should record the serial numbers of inspection instruments:
- A. Each time the instrument is used
- B. Only if the specification requires it
- C. Only if the instrument is suspected of not working properly
- D. Only when verifying accuracy of the instrument
Answer: A
NEW QUESTION # 34
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Abrasive blast nozzles
- C. Hand tools
- D. Airless spray equipment
Answer: A
NEW QUESTION # 35
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. a) & b)
- C. It is the only deliverable item provided by the inspector
- D. a) only
Answer: A
NEW QUESTION # 36
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 90% of the specified maximum thickness
- B. 70% of the specified maximum thickness
- C. 100% of the specified maximum thickness
- D. 80% of the specified minimum thickness
Answer: D
NEW QUESTION # 37
The NACE Inspector should perform tests for soluble salts:
- A. After surface preparation
- B. When specified
- C. Prior to coating application
- D. Prior to surface preparation
Answer: B
NEW QUESTION # 38
......
Latest 100% Passing Guarantee - Brilliant NACE-CIP1-001 Exam Questions PDF: https://www.practicedump.com/NACE-CIP1-001_actualtests.html
Practice Examples and Dumps & Tips for 2024 Latest NACE-CIP1-001 Valid Tests Dumps: https://drive.google.com/open?id=1zqEIjHFMCvJ7G-xRpgeT0MoQapJSXU2D