[Oct-2023] Verified NACE Exam Dumps with NACE-CIP2-001 Exam Study Guide
Best Quality NACE NACE-CIP2-001 Exam Questions PracticeDump Realistic Practice Exams [2023]
NEW QUESTION # 13
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION # 14
The HATE adhesion tester uses
- A. mechanical means only to apply pressure to the test dolly.
- B. a hydraulic piston to apply pressure to the test dolly.
- C. a special tape to apply pressure to the test dolly.
- D. compressed air to apply pressure to the test dolly.
Answer: B
NEW QUESTION # 15
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Fusion Bonded Epoxy
- B. 3-Layer Polyethylene (PE)
- C. 2-Layer Polyethylene (PE)
- D. Coal Tar Enamel
Answer: B
NEW QUESTION # 16
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A destructive paint inspection Tooke gauge
- B. A mechanical adhesion tester
- C. A set of 14 pencils of varying hardness
- D. A hardness tester
Answer: A
NEW QUESTION # 17
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Gel stage
- C. Flow stage
- D. Wetting stage
Answer: C
NEW QUESTION # 18
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Don your air supplied respirator and continue the testing
- B. Exit the tank and document the incident in your daily report
- C. Investigate to find the source of the odor
- D. Exit the tank and immediately and report the problem to the nearest safety supervisor
Answer: D
NEW QUESTION # 19
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Review the NCR with the other Inspector
- B. Consult your supervisor
- C. Verbally challenge the NCR
- D. Request a re-blast of the item in question
Answer: B
NEW QUESTION # 20
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Move the nozzle quicker
- B. Lower the blast pressure
- C. Increase the standoff distance
- D. a), b) and c)
Answer: D
NEW QUESTION # 21
It is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION # 22
When environmental enclosures are being used an inspector needs to be concerned about:
- A. a), b), and c)
- B. Lighting
- C. Air changes
- D. Structural integrity
Answer: A
NEW QUESTION # 23
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Glue failure
- B. Cold flow or creep
- C. Cohesion failure
- D. Adhesion failure
Answer: B
NEW QUESTION # 24
Pre-cleaning of work pieces will NOT remove
- A. dirt.
- B. oil or grease.
- C. snow, ice or water.
- D. mill scale.
Answer: D
NEW QUESTION # 25
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Concrete
- B. Liquid epoxies
- C. Coal Tar Enamel
- D. Heat-shrink sleeves
Answer: B
NEW QUESTION # 26
Cold-applied tape
- A. are identifiable by its distinct colors, usually light blue, green, Or Grey.
- B. is typically green or led and looks like "painted" finish.
- C. have a cross-linked polyethylene backing and a heat-activated adhesive.
- D. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
Answer: D
NEW QUESTION # 27
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Ignore the situation
- B. Require the Applicator to remove the coating
- C. Advise the Owner and write a Non-Conformance report
- D. Stop the job
Answer: B
NEW QUESTION # 28
......
Authentic Best resources for NACE-CIP2-001: https://www.practicedump.com/NACE-CIP2-001_actualtests.html
NACE-CIP2-001 Test Engine Practice Exam: https://drive.google.com/open?id=1fjZ6Q_FT2hQ56WMn7vWjwme0vNh2yuVi